How Plumbers Replace Bathroom and Kitchen Sink Faucets

If you are considering upgrading your bathroom and kitchen sink faucets, you have come to the right place. The following explanation will make your task much easier and will save your time as well.

However, before we start, make sure that you have following materials ready with you.

- New faucet assembly
- Basin wrench
- Adjustable wrenches
- Slip-joint pliers
- Scouring pad

Now follow these simple steps. (Assuming that you are replacing the old two-handled faucet with the more modern single-handled type)

Replacing Kitchen Sink Faucets 1. Before you start, go at the shut-off valves under the sink, and turn off the water.

2. Open the faucet so that it could drain any excess water.

3. The next step is to disconnect the hot and cold water supply lines from the shutoff valves. You can use a small adjustable-wrench to do this.

4. Reach up behind the faucet. You will find the coupling nuts that connect the supply tubes to the faucet. Unscrew the same using a basin wrench.

5. Behind the faucet, you will also find mounting nuts that hold the faucet in place. Remove these nuts using the same basin wrench.

6. Now that you have disconnected the mounting nuts, you can lift out the old faucet. Lifting it out, disconnect the sprayer hose from the assembly using an adjustable wrench.

7. Lift out the sprayer hose, and remove the faucet.

8. Once you have removed the faucet, clean the surface of the sink thoroughly with a scouring pad.

9. Remove the escutcheon cap and replace the same with the one that is included with your new faucet.

10. Now you are ready to make the new connection. Bring your new sprayer hose, and slip it down through the sprayer hole.

11. Feed the sprayer hose up through the center faucet hole, and connect the hose through the sprayer nipple using an adjustable wrench.

12. If the hot and cold supply tubes of the new faucet have a different length, attach flexible connectors to the fittings on the supply tubes. Hold the faucet fitting stationary with one wrench and tighten each connection with another wrench.

13. Insert and feed the supply lines and the connectors into the center hole, and then seat the faucet.

14. Now crawl up under the sink and in order to hold the faucet in place, install a washer and nut to the end bolts.

15. First, tighten the nuts by hand, and then with a basin wrench.

16. Connect the supply lines to the shutoff valves, and turn the water on.

17. Turn on the faucet and check for leaks.

Replacing Bathroom Sink Faucets 1. Go underneath the sink. Turn off the water. Loosen the collar nuts on the drainpipe.

2. Drain any excessive water, and then remove the drainpipe.

3. Loosen the nuts that hold the pop-up assembly in place under the sink using slip-joint pliers.

4. Unscrew the pop-up flange in order to free the assembly underneath the sink.

5. Remove the fittings that join the supply lines of the old faucet to the shutoff valves, using a wrench.

6. Repeat the steps 4-15 as explained above for replacing kitchen faucet.

7. Now, you have to install the pop-up assembly.

8. Push the pop-up rod down through the body of the faucet.

9. Attach the flat bar.

10. At the bottom of the new flange, use a little plumber's putty to hold the tailpiece so that the whole assembly protrudes up through the drain hole in the sink.

11. Spin the ring to position the same with the tailpiece under the sink.

12. In order to secure pop-up housing in place, tighten the nut on top of the tailpiece.

13. Hook up the pop-up lever onto the flat bar in order to secure it to the pop-up housing.

14. Drop the stopper into the drain hole.

15. Replace the drainpipe.

16. Tighten the collar nuts.

17. Turn on the faucet and check for leaks.

Hence, replacing a kitchen and a bathroom faucet is almost similar except for the work related to the pop-up assembly that is included with the bathroom sink.

Owen Walcher writes for the Best Plumber Resource which provides plumbing tips to consumer and helps people find quality plumbers in Georgia. plumbers.besthomeresource.com

Dealing With The Leaking Bathtub Faucet

Drip, drip, drip. A leaky bathtub faucet is a common problem in many homes. If you have one, the good news is they are usually fairly simple to take care of.

The repair of leaky faucets is another often minor plumbing job that can be done by yourself with a minimum of effort and with no special tools. Although this may be true, it is an extremely important job. A single pinhole leak in a water pipe can waste up to 70 gallons of water per day. A badly leaking faucet can waste even more. This is a serious environmental issue today. There are some who claim that the very population levels of the world are depending on the supply of potable water. And we are already running behind.

There are two major types of faucets. The most common one in older homes is called the compression faucet. This faucet uses a rubber washer that is compressed when the valve is closed. The compressed washer expands and seals off the water flow. This process is hard on the washer and after a time they will wear out and need to be replaced.

When you go to replace the washer, you must first shut off the water supply to the faucet. Sometimes it is possible to do this at a more local spot close to the faucet, but other times it is necessary to shut off the main water supply to the home to isolate the faucet. It is a good idea to protect the enamel of the bathtub with towels to protect it from chips from dropped tools. Another good preparation idea is to cover drains to prevent small pieces from being dropped into them.

When you take apart the faucet to get to the washer, make diagrams or notes of exactly how you do so. This will make it easier to put it back together. Normally, the replacement of the washer will solve the leak problem. Keep spare washers handy in your tool box. You will need them again before long.

The newer type of faucet is called a washer less faucet. The name tells it all. The valve opens and shuts by an actual physical closing of the valve. You can usually tell if your faucet is compression or washer less just by feel. A compression faucet needs to be tightened to get it closed. The washer less faucet glides easily into place and does not need additional pressure to cut off the flow. There are fewer problems with leaking on washer less faucets. They tend to be either working or not. When they wear out, or do not operate properly, they should be replaced.

Fred Linson is with PlumbingStop.com - providing basic plumbing information and more resources.